Windows: commercial building survey
A window measurement template: one section per facade, one row per opening, the glazed area and perimeter per facade and for the building.
No credit card. Cancel anytime.
Feet and inches or metric: your choice. One switch on the sheet converts every measurement.


What you measure
The template's tables and their columns, as the app shows them. Calculated columns fill in as you type.
Openings
- Mark
- TypeChoices: Fixed Fixed over awning Casement Awning Hopper Projected Single hung Sliding Storefront Aluminum entrance door Curtain wall (glazed)
- Width (masonry opening)
- Height (masonry opening)
- Quantity
- Area per unit calculated
- United inches (W + H) calculated
- Opening area calculated
- Caulk perimeter calculated
- ConditionChoices: Good Monitor Replace
- FrameChoices: Aluminum Steel Wood Vinyl Clad
- GlazingChoices: Single Double (insulated) Triple (insulated) Laminated Tempered Wired (check the code) Low-E
- PanesChoices: Single Double (sealed unit) Triple (sealed unit)
- Glass typeChoices: Annealed Heat-strengthened Tempered Laminated Wired (check the code)
- Low-e coatingChoices: Yes No Unknown
- Safety glazing locationChoices: Yes No
- DeficienciesChoices: None observed Sealed unit failure (fogging) Broken or cracked glass Condensation or frost Air leakage Water infiltration Frame corrosion or rot Thermal break failure Hardware or operation Weatherstripping Perimeter sealant failure Glazing putty or gasket failure Blocked weep holes
- Notes
See these tables calculate with your own measurements, no account.
Try this templateMore templates: Windows and window film
Windows and doors: replacement measure
The windows and doors of a house, room by room: replacement type, three readings with the smallest kept, squareness, depth, hinges and glass.
You get: Area
Commercial window film
Film for multi-story buildings, floor by floor: glass area, film product and linear elements.
You get: Glass Surface Area Total Area Panes over 40 sq ft
Window film
Film for a house or a small building: windows, skylights and glass doors, film area per type, safety film anchoring.
You get: Total Area Panes over 40 sq ft Anchored length
About this template
One section per facade with a subsection per floor, and one row per opening: mark, type, width, height and quantity of the masonry opening give the opening area and the caulk perimeter, with the area per unit, united inches, condition, frame, panes, glass, low-e coating, safety glazing location and deficiencies, and totals per facade and for the whole building. A building form, filled once, holds the name, address, year built, wind exposure, climate zone and the PCB and asbestos checks.
Guide and sources
Read the guide and sources
Measure each opening three times across and three times up, then keep the smallest of each; the readings should agree within 1/8 in. Note where you measured: masonry opening, rough opening, existing frame or glass. Never assume two look-alike windows are the same size.
The supplier deducts a clearance from your smallest measure, about 1/4 to 5/8 in per side depending on the product. Codes count fenestration area on the rough opening; curtain walls to mullion centrelines.
The perimeter is measured once and sealed twice: outside with backer rod and sealant, inside with an air seal.
For the right performance class (CW or AW for most commercial buildings), note the storeys, each opening's height above the ground and the wind exposure: open or rough terrain in the NBC, exposure B, C or D in ASCE 7, with hills and escarpments raising the load. MesuPro does not compute the wind class; the supplier does. The energy code's climate zone sets the thermal targets: 4 to 8 in Quebec, 1 to 8 with A, B or C by county in the US. Storefronts and curtain walls are separate systems, outside the window standard.
Glass in or near doors, large low panes and stair glazing must be safety glass; wired glass no longer qualifies. Caulk applied from about 1950 to 1979 may contain PCBs, and old glazing putty and caulk can contain asbestos: have them tested before removal, and note the results in the building form.
Sources
- NAFS (101/I.S.2/A440) paywalled Standard
- Jeld-Wen, measuring guide Manufacturer data
- AAMA 2410 paywalled Standard
- Marvin, measuring instruction Manufacturer data
- United inches (dealer pricing) Rule of thumb
- Pella, opening clearance Manufacturer data
- Efficient Windows, frame types Trade association
- IBC 2021, 2406.1.1 and 2406.2 Code
- IBC 2021, 2406 Code
- EPA, PCBs in caulk Government
- ASCE 7-22 paywalled Standard
- DOE, climate regions by county Government
- EPA-530-R-23-015 Government
- EPA, asbestos in window caulk Government
- Jeld-Wen Canada, size guide (FR) Manufacturer data
- NBC Part 9 (BCBC 2018), 9.6 and 9.7 Code
- CAN/CGSB-12.1 paywalled Standard
- NBC 2020, 3.3.1.20 Code
- NBC 2020, 9.6.1.4 Code
- SOR/2008-273 (PCB) Government
- BCBC 2018, 4.1.7 (NBC wind) Code
- Quebec Construction Code, ch. I.1 Code
Your trade isn't listed? The AI assistant builds your form.
No credit card. Cancel anytime.