Free roofing calculator: sloped roof area, squares, bundles and accessories

Get the sloped area, roof squares and shingle bundles of a gable or hip roof, with the underlayment, ridge cap, drip edge, starter and eave membrane, in seconds, free and without an account. One row per roof face: its width along the eave, its narrowing at the ridge when the face is not a rectangle (a hip roof's long side narrows by twice its run, a hip end by its full width: a triangle), its horizontal run (plan view) and its pitch, or the slope length measured on the roof, and its waste. Below, the roof's lines (ridges and hips, eaves, rakes) and the coverage printed on each accessory's wrapper. You get the sloped roof area, the squares (one square covers 100 sq ft) and what to order.

How to fill it in

One row per roof face: its width along the eave, its narrowing at the ridge when the face is not a rectangle (a hip roof's long side narrows by twice its run, a hip end by its full width: a triangle), its horizontal run (plan view) and its pitch, or the slope length measured on the roof, and its waste. Below, the roof's lines (ridges and hips, eaves, rakes) and the coverage printed on each accessory's wrapper. You get the sloped roof area, the squares (one square covers 100 sq ft) and what to order.

Units
Feet and inches

Face 1

ft
ft
ft
/12
ft
%
Typical value (GAF, bundles per square)
sq ft

Lines and accessories (optional)

One line for the whole roof: leave empty what you do not order. The eave membrane runs up the slope from the edge, far enough to pass the inside of the wall: at least 900 mm, and 300 mm past it (NBC); 24 in past it (IRC).

ft
ft
ft
ft
ft
ft
ft
sq ft

Result

Fill in the fields to see the result.

A quick estimate, for one shingle product. The template handles the whole job: several lines, dormers, notes and photos per face, and totals by section.

The whole job, not only this calculation

For roofing contractors and their crews, the template does what this page cannot: the whole job on one sheet, every measurement on its own line, saved in the client's project with a PDF or Excel report.

How it is calculated

Pitch factor = square root of (1 + (pitch / 12)²). Real area = (width - narrowing at the ridge / 2) x the larger of the slope length and the horizontal run x pitch factor, face by face: with a slope length, no pitch is needed. The first factor is a trapezoid's average width; a narrowing equal to the width gives a triangle, no narrowing a rectangle. Area with waste = real area x (1 + waste), each face with its own: 10% to start, the rule of thumb the template gives (Owens Corning: 10 to 15%, more on a cut-up roof). Squares = area with waste / 100 sq ft. Bundles = squares x bundles per square: 3 for most shingles, 4 or 5 for some heavy designer shingles (check the wrapper). Underlayment rolls = real area / roll coverage. Ridge cap bundles = ridges and hips / coverage per bundle. Drip edge = (eaves + rakes) / 9 ft 10 in: a 10 ft piece laps the next by 2 in (IRC R905.2.8.5). Starter bundles = starter length / coverage per bundle. Eave membrane = eaves x its depth up the slope, then rolls = that area / roll coverage. Each count is rounded up once, on the total. No coverage comes filled in: read it on the wrapper.

Example: a hip roof

A 40 ft by 28 ft house with a 6/12 pitch all around. A hip roof has two trapezoid faces (the long sides) and two triangles (the hip ends). Every face rises from the eave to the ridge over the same horizontal run, half of 28 ft, so 14 ft, and the ridge is 40 - 28 = 12 ft long. For each face, enter its width at the eave and how much it narrows at the ridge: eave - ridge, so 28 ft for both shapes (a hip end narrows by its full width).

FaceCountEaveRidgeNarrowing at the ridge
Trapezoid (long side)240 ft12 ft28 ft
Triangle (hip end)228 ft028 ft

In the calculator, one row per face: two trapezoids 40 ft wide and two triangles 28 ft wide, all narrowing by 28 ft at the ridge, each with a 14 ft horizontal run, a 6/12 pitch and 10% waste. Sloped roof area: 1,252.2 sq ft, 1,377.4 sq ft with waste, so 13.77 squares and 42 bundles of shingles. The lines: four hips of 21 ft (14 ft of run x 1.5, the hip factor at 6/12) and the 12 ft ridge make 96 ft, and the eaves run all around the house, 136 ft. With the coverages the template's own example types, 33 ft per bundle of ridge cap and 400 sq ft per roll of underlayment: 3 bundles of ridge cap, 4 rolls of underlayment and 14 pieces of drip edge. A gable roof on the same house (two faces of 40 ft by 14 ft) gives the same area: at the same pitch, only the plan area counts. The eave overhang is not counted here: add it to your measurements.

FAQ

How many square feet does a bundle of shingles cover?

Most asphalt shingles, 3-tab and architectural, come 3 bundles to the square, which is 100 sq ft of roof: about 33 sq ft per bundle. Some heavier designer shingles take 4 or 5 bundles per square (GAF). The bundles per square are printed on the wrapper: the calculator starts at 3 and you can change it.

How do you figure roofing squares?

Face by face: the plan area (width x run) times the pitch factor, or the width times the length measured up the slope. At a 6/12 pitch the factor is 1.118, so 100 sq ft seen from above is about 112 sq ft of roof. Add the faces, add the waste, then divide by 100: that is the number of squares. The roof measuring guide shows both ways, from the ground or on the roof.

The whole job in MesuPro

For roofing contractors and their crews: every employee measures with the same form, the math is done as they type, and the office finds the sheet and its PDF or Excel report. 14-day free trial, no credit card.

Roofing: measurement and materials⁠

Real sloped area from the pitch, squares, shingles, underlayment, ridge cap and drip edge.

You get: Real area Area with waste Squares

Your trade isn't listed? The AI assistant builds your form.

Start your 14-day free trial

No credit card. Cancel anytime.

Did this page help you?

Feedback on this calculator

A result that looks wrong, a missing case, an idea? Tell us.

Please don't put personal details in this box.