Free drywall calculator: sheets, joint compound, tape and screws

Get the drywall sheets, joint compound, tape and screws for a room in seconds, free and without an account. One row per wall or ceiling: its length, height or width, and the openings you deduct. Enter the sheet size, your waste and the rates read from the data sheets: the calculation gives the sheets, the compound, the tape and the screws. Pick a maker to fill the compound and tape rates it prints (USG, CGC, National Gypsum, CertainTeed), and your framing spacing for CGC's screw table: the values stay editable. Each surface's line shows its own board area and sheets.

Updated

How to fill it in

One row per wall or ceiling: its length, height or width, and the openings you deduct. Enter the sheet size, your waste and the rates read from the data sheets: the calculation gives the sheets, the compound, the tape and the screws. Pick a maker to fill the compound and tape rates it prints (USG, CGC, National Gypsum, CertainTeed), and your framing spacing for CGC's screw table: the values stay editable. Each surface's line shows its own board area and sheets.

Units
Feet and inches

Surface 1

ft
ft
sq ft
ft
ft
%
gal/1000 sq ft
ft/1000 sq ft
screws/1000 sq ft
ft
ft

Result

Fill in the fields to see the result.

A quick estimate, for one sheet size and one product: the sheets of two products never add up. The template handles the whole job: room by room, board types, corners and trim, level of finish and fire separation.

The whole job, not only this calculation

For drywall contractors and their crews, the template does what this page cannot: the whole job on one sheet, every measurement on its own line, saved in the client's project with a PDF or Excel report.

The data sheets' rates (reference)

As printed, per area of board. Beware: some sheets print the per-1,000 sq ft figure unchanged under "per 100 m²" (it is per 93 m²). Your product's exact rate is on its data sheet.

Data sheetMaterialPublished rate
USG J1969All purpose compoundAbout 10 gal per 1,000 sq ft
National GypsumReady-mix compoundsAbout 123 to 140 lb (9 gal) per 1,000 sq ft
USG J443727Paper tapeAbout 370 ft per 1,000 sq ft
CGC handbookScrewsAbout 1,000 per 1,000 sq ft at 16 in framing, 850 at 24 in

Sources: USG, all purpose compound; National Gypsum, construction guide; USG, paper joint tape; CGC handbook

Board and fasteners: the rules (reference)

What the codes and makers say, as read. No maker publishes a waste percentage: CGC only says to allow for loss.

Rule as read
Thickness and fastenersIRC Table R702.3.5: 1/2 and 5/8 in board on ceilings at 16 in, or 24 in perpendicular, nails 7 in or screws 12 in; on walls at 24 in, screws 12 in (16 in at 16 in framing)
Fastener spacingGA-216: screws at most 12 in on ceilings and 16 in on walls framed at 16 in; at least 3/8 in from edges
SizesSheets 4 ft wide, 8 to 12 ft long; 1/2 in regular and 5/8 in Type X
OpeningsCertainTeed counts them as board; USG subtracts only the large ones

Sources: IRC 2021, R702.3.5; GA-216; National Gypsum, construction guide; CertainTeed, installation guide; USG, installation guide

Before you open a wall or tape: the cautions (reference)

What the sources say, as read.

Caution
Older materialsHealth Canada lists paint, putty, drywall, caulking, sealants and spackling among older materials that may contain asbestos: have them tested before sanding or breaking
Lead paintThe EPA RRP rule covers paint disturbed in homes built before 1978: certified firms and renovators
Garage1/2 in gypsum board on the garage side, 5/8 in Type X under habitable rooms above it
Wet areasWater-resistant backing board is not for direct exposure to water or continuous high humidity

Sources: Health Canada, asbestos; EPA, RRP rule; IRC 2021, R302.6; IRC 2021, R702.3.7

How it is calculated

Board area = length x height (or width) - openings deducted, for each surface. Sheets = area x (1 + waste) / (sheet width x length), rounded up to the sheet on the total. Compound = area x rate / 1,000 (gal per 1,000 sq ft), tape = area x rate / 1,000 (ft per 1,000 sq ft), screws = area x rate / 1,000, rounded up. Trim pieces = trim run / piece length, rounded up. No sheet size or waste comes filled in. With a maker picked, the rate it prints fills the field, converted exactly to the unit shown; a maker that prints no figure for a field leaves it empty, and a range is shown in the note, never filled in. With Other picked, every rate comes from your data sheets.

Example: a bedroom takeoff for your bid

For drywall contractors pricing a bedroom: four walls 12 ft and 11 ft long and 8 ft high, with a 15 sq ft window and a 21 sq ft door deducted, and a 12 x 11 ft ceiling, each surface on its own row. With 4 x 12 sheets, 10% waste, USG's 10 gal of compound and 370 ft of paper tape per 1,000 sq ft and CGC's 1,000 screws per 1,000 sq ft at 16 in framing: 464 sq ft of board, 11 sheets, 4.6 gal of compound, 172 ft of tape and 464 screws. The ceiling alone is 132 sq ft of that, and GA-216 spaces its screws at most 12 in apart. Your prices and labor stay yours.

FAQ

How many sheets of drywall do I need?

Add up the board on every wall and ceiling, take off the openings you deduct, add your waste and divide by one sheet: 32 sq ft for a 4 x 8, 48 sq ft for a 4 x 12. With 1,500 sq ft of board and 10% waste in this example, that is 1,650 sq ft: 52 sheets of 4 x 8 or 35 of 4 x 12. Count the walls and ceilings, not the floor area of the house. No maker publishes a waste percentage, so the one you enter is yours.

How much drywall mud do I need?

USG prints about 10 gal of all purpose compound per 1,000 sq ft of board, and National Gypsum about 9 gal (123 to 140 lb) of its ready-mix. At USG's rate, that is about 0.32 gal per 4 x 8 sheet, or 15 gal for 1,500 sq ft. CertainTeed prints a range instead, by the thickness applied. Divide by the size of your product's pail or box.

How much tape and how many screws per sheet of drywall?

Paper tape: about 370 ft per 1,000 sq ft of board (USG), 375 ft (National Gypsum), so about 555 ft for 1,500 sq ft. Screws: CGC's table counts about 1,000 per 1,000 sq ft with framing at 16 in and 850 at 24 in, about 32 per 4 x 8 sheet at 16 in and 27 at 24 in. GA-216 spaces them at most 12 in apart on ceilings.

Is a sheetrock calculator any different?

Sheetrock is USG's brand of gypsum board: sheets, compound, tape and screws are counted the same way for every brand. Pick USG in the finish list to fill the rates USG prints, or Other to enter those of your product.

Can I use it for a drywall bid?

It gives the quantities your bid starts from: sheets, compound, tape and screws. Your prices and labor stay yours. For a whole house, the drywall survey template below takes every room, the board types, corners and trim, and puts the totals in a PDF or Excel report. You can try it without an account.

Measuring a whole drywall job for a bid?

For drywall contractors and their crews: with the drywall survey, everyone measures with the same form, wall by wall and ceiling by ceiling, with the openings, the board type and the sheet size, then the corners and trim. The survey totals the drywall sheets per product, the trim pieces, and the compound, tape and screws for the whole job, and the office finds a PDF or Excel report with every number for your bid. Your prices stay yours.

Try the drywall survey, no account

The whole job in MesuPro

For drywall contractors and their crews: every employee measures with the same form, the math is done as they type, and the office finds the sheet and its PDF or Excel report. 14-day free trial, no credit card.

Drywall survey⁠

Walls and ceilings room by room, sheets, trim, compound, tape and screws, GA-214 finish levels, repairs and textured ceilings.

You get: Board area Sheets Trim pieces

Your trade isn't listed? The AI assistant builds your form.

Start your 14-day free trial

No credit card. Cancel anytime.

Did this page help you?

Feedback on this calculator

A result that looks wrong, a missing case, an idea? Tell us.

Please don't put personal details in this box.