Roofing: inspection & measurement

Face by face: area, pitch, material, condition, waste and squares, with photos, and the attic ventilation.

No credit card. Cancel anytime.

Feet and inches or metric: your choice. One switch on the sheet converts every measurement.

Roofing: inspection & measurement: a filled-in survey in MesuPro
Roofing: inspection & measurement: the same sheet on a phone
A survey made with this template, in the app.

What you measure

The template's tables and their columns, as the app shows them. Calculated columns fill in as you type.

Roof planes

  • Roof plane
  • Rafter length (eave to ridge)
  • Horizontal run (plan view, instead of the rafter length)
  • Width along the eave
  • Narrowing at the ridge (trapezoid, or the full width for a hip end)
  • Pitch (X/12)
  • Pitch factor calculated
  • Area calculated
  • Pitch rangeChoices: Flat (under 2/12) Low (2/12 to 4/12) Conventional (4/12 to 8/12) Steep (8/12 to 12/12) Very steep (over 12/12)
  • MaterialChoices: 3-tab shingles (traditional) Architectural shingles (laminated) Asphalt shingles Metal Modified bitumen (SBS, 2-ply) EPDM membrane TPO membrane Membrane (EPDM/TPO) Built-up (tar and gravel) Cedar shakes Slate Other
  • WorkChoices: Replace Repair No work Not in scope
  • ConditionChoices: Good Fair Poor End of life Replace
  • Waste
  • Area with waste calculated
  • Squares (100 sq ft) calculated
  • Bundles per square (100 sq ft)
  • Bundles calculated
  • Notes

Roof lines

  • Line
  • Ridge and hips (length)
  • Ridge cap bundle coverage
  • Ridge cap bundles calculated
  • Eaves (length)
  • Rakes (length)
  • Drip edge and rake trim (perimeter)
  • Drip edge pieces (10 ft) calculated
  • Starter strip (length)
  • Starter bundle coverage
  • Starter bundles calculated
  • Eave protection depth (along the slope)
  • Eave membrane roll coverage
  • Eave protection area calculated
  • Eave membrane rolls calculated
  • Valleys (length)
  • Wall and step flashing (length)
  • Notes

Penetrations

  • Location
  • Plumbing vent boots
  • Roof vents
  • Chimneys
  • Skylights
  • Exhaust fan vents
  • Notes

Attic ventilation

  • Attic or roof space
  • Insulated ceiling area
  • Vent ratioChoices: 1/300 1/150
  • Vent area at 1/300 calculated
  • Vent area at 1/150 calculated
  • Vent area at this ratio (net free area) calculated
  • Share near the ridge
  • At this ratio near the ridge calculated
  • At this ratio at the soffits calculated
  • Existing near the ridge
  • Existing at the soffits
  • Gap near the ridge calculated
  • Gap at the soffits calculated
  • Exhaust vent (product)
  • Exhaust area per foot (ridge vent)
  • Ridge vent to add calculated
  • Exhaust area per vent (roof louver)
  • Roof vents to add calculated
  • Intake vent (product)
  • Intake area per foot (continuous)
  • Continuous intake to add calculated
  • Intake area per vent
  • Intake vents to add calculated
  • Notes

See these tables calculate with your own measurements, no account.

Try this template

More templates: Roofing

Roofing: measurement and materials⁠

Real sloped area from the pitch, squares, shingles, underlayment, ridge cap and drip edge.

You get: Real area Area with waste Squares

Metal roofing survey⁠

Metal roofs plane by plane: panels from the coverage width, length to order, screws, strapping, snow guards, trims and flashings.

You get: Area Panels Panel length to order

Low-slope roof survey⁠

Flat roofs section by section: slope, system in place, test cuts, drains, upstands, rolls and boards.

You get: Area Test cuts Upstand run

About this template

Measure each roof plane along the slope or in plan view with its pitch, record material, condition and work, and get the area with waste, the squares and the shingle bundles to order, plus roof lines and penetrations. Waste covers the field shingles: starter and ridge cap come from the roof lines.

Guide and sources

Read the guide and sources

Each roof area (main roof, garage, porch) is one subsection with a tab for its planes, its lines and its penetrations: add the next one with "Add a roof area" and rename it. Measure each roof plane along the slope, or in plan view with its pitch (X in 12): the app works out the real area. Type the waste for each plane: about 10% on a gable roof and 15% on a hip roof is a trade rule of thumb, more on a cut-up roof. Starter strip, ridge cap, drip edge and eave membrane are counted in the roof lines, from the eaves and rakes you measure. The attic ventilation tab gives the net free vent area the codes ask for: type the insulated ceiling area, the ratio and the share near the ridge, then the area of the vents in place, from their labels.

A 10 ft drip edge piece covers 9 ft 10 in, because pieces lap 2 in. Asphalt shingles need at least 2/12, and from 2/12 to 4/12 the IRC asks for two underlayment layers. Where ice dams form, the ice barrier runs to at least 24 in inside the exterior wall. Bundle and roll coverage varies by product: read the wrapper.

In Quebec, the code (NBC 2020 as modified) asks for eave protection at least 900 mm up the slope and 300 mm past the inside of the wall, and the AMCQ specification asks for more: 1 m past the wall, a 4/12 minimum and underlayment over the whole roof.

The vents to add: for each attic, type the exhaust and intake products and their net free area from the maker's sheet, per foot for a ridge vent or a continuous intake (GAF Cobra ridge vents 12.5 to 18 sq in per foot, the IntakePro 9), or per vent for a roof louver or a soffit vent (GAF RV50: 50 sq in). The sheet divides the area still to vent near the ridge and at the soffits (the whole area when no existing vent is typed) and adds the feet and the vents per product, the vents rounded up once.

Sources

  • IRC 2021, R905.2.2 CodeInternational Residential Code 2021, R905.2.2 Slope, International Code Council (read in a state adoption), 2021. Checked Oct 7, 2026
  • IRC 2021, R905.1.1 CodeInternational Residential Code 2021, R905.1.1 and Table R905.1.1(2) Underlayment, International Code Council (read in a state adoption), 2021. Checked Oct 7, 2026
  • Owens Corning, waste (rule of thumb) Rule of thumbOwens Corning, DIY roofing: how much waste to plan, Owens Corning, Web page. Checked Oct 7, 2026
  • GAF, bundles per square Manufacturer dataGAF, How many bundles of shingles are in a square, GAF, Web page. Checked Oct 7, 2026
  • Makers' data, ridge caps Manufacturer dataHip and ridge cap coverage per bundle: GAF Seal-A-Ridge and TimberTex, CertainTeed Shadow Ridge and Mountain Ridge, Owens Corning ProEdge, IKO Hip and Ridge 12, BP Crown Ridge, GAF, CertainTeed, Owens Corning, IKO, BP, Data sheets checked 2026-10. Checked Oct 7, 2026
  • IRC 2021, R905.2.8.5 CodeInternational Residential Code 2021, R905.2.8.5 Drip edge, International Code Council (read in a state adoption), 2021. Checked Oct 7, 2026
  • Makers' data, starter strips Manufacturer dataStarter strip coverage per bundle: GAF Pro-Start, CertainTeed SwiftStart, Owens Corning Starter Strip Plus, IKO Leading Edge Plus, BP, GAF, CertainTeed, Owens Corning, IKO, BP, Data sheets checked 2026-10. Checked Oct 7, 2026
  • IRC 2021, R905.1.2 CodeInternational Residential Code 2021, R905.1.2 Ice barriers, International Code Council (read in a state adoption), 2021. Checked Nov 15, 2026
  • Makers' data, eave membrane Manufacturer dataSelf-adhered ice and water membrane roll sizes: IKO StormShield, GAF WeatherWatch, IKO, GAF, Data sheets checked 2026-10. Checked Oct 7, 2026
  • IRC 2021, R806.2 CodeInternational Residential Code 2021, R806.2 Minimum vent area, International Code Council (read in a state adoption), 2021. Checked Oct 7, 2026
  • GAF, ventilation brochure (2019) Manufacturer dataGAF attic ventilation brochure (Cobra ridge vents, Master Flow vents), GAF (the maker; the copy a distributor hosts), brochure of August 2019. Checked Oct 16, 2026
  • IRC 2021, R908.3 CodeInternational Residential Code 2021, R908.3 Roof recover and replacement, International Code Council (read in a state adoption), 2021. Checked Nov 15, 2026
  • NBC 2020, Table 9.26.3.1 CodeNational Building Code of Canada 2020, Table 9.26.3.1 Roof slopes for asphalt shingles, National Research Council Canada, 2020 (Quebec: Code de construction, chapitre I, in force 2025-04-17). Checked Oct 7, 2026
  • NBC 2020, 9.26.8 CodeNational Building Code of Canada 2020, 9.26.8 Asphalt shingles on low slopes, National Research Council Canada, 2020 (Quebec: Code de construction, chapitre I, in force 2025-04-17). Checked Oct 7, 2026
  • NBC 2020, 9.26.7.2 CodeNational Building Code of Canada 2020, 9.26.7.2 Starter strip, National Research Council Canada, 2020 (Quebec: Code de construction, chapitre I, in force 2025-04-17). Checked Oct 7, 2026
  • NBC 2020, 9.26.5.1 CodeNational Building Code of Canada 2020, 9.26.5.1 Eave protection, National Research Council Canada, 2020 (Quebec: Code de construction, chapitre I, in force 2025-04-17). Checked Oct 7, 2026
  • NBC 2020, 9.19.1.2 CodeNational Building Code of Canada 2020, 9.19.1.2 Attic and roof space venting, National Research Council Canada, 2020 (Quebec: Code de construction, chapitre I, in force 2025-04-17). Checked Oct 7, 2026
  • AMCQ, Division 4 (2025) Trade associationAMCQ, Devis couvertures, Division 4: bardeaux d'asphalte, Association des maîtres couvreurs du Québec, October 2025. Checked Oct 15, 2026
  • AMCQ, bulletin 5 (2023) Trade associationAMCQ, Bulletin technique 5: ventilation des vides sous toit, Association des maîtres couvreurs du Québec, Revised 2023-11-21. Checked Oct 7, 2026

Your trade isn't listed? The AI assistant builds your form.

No credit card. Cancel anytime.