Free window film calculator: film area, panes and rolls

Get the window film area and the rolls to order in seconds, free and without an account. One row per pane size: its width, height and how many identical panes. The calculation gives the film area, the large panes to check before installing and, from your roll size, an estimate of the rolls. In metric or imperial.

How to fill it in

One row per pane size: its width, height and how many identical panes. The calculation gives the film area, the large panes to check before installing and, from your roll size, an estimate of the rolls. In metric or imperial.

Units
Feet and inches

Pane 1

in
in
in
ftTypical value (IWFA, safety and security guide)
%

Result

Fill in the fields to see the result.

A quick estimate, without the cutting plan. The template handles the whole job: panes by facade and floor, film by product, frames and edges, review notes and totals.

The whole job, not only this calculation

For window film and screen installers and their crews, the templates do what this page cannot: the whole job on one sheet, every measurement on its own line, saved in the client's project with a PDF or Excel report.

Film and glass: when to check before installing (reference)

Solar film heats the glass. The film industry association (IWFA) gives these general rules, for when the film maker gives none, as read:

What the source says
Large panesNo solar film on an annealed sealed unit over 40 sq ft (3.7 m²) or a single annealed pane over 100 sq ft (9.3 m²)
Thick, tinted or coated glass, partial shadingCheck film and glass compatibility before installing
Low-e glassWhere the coating sits varies from window to window: check compatibility against the glass or film maker's warranty conditions
Tempered or annealedTempered glass carries an etched mark in a corner; without one, check the glass type before installing

Source: IWFA, advanced solar guide

Rolls and cutting (reference)

The trade's figures, cited as a guide: your roll and your cut stay yours.

What the sources say
Rolls36 to 72 in (91 to 183 cm) wide by 100 ft (30.5 m)
CuttingEach piece cut a little larger than the glass, then trimmed in place
EdgeAn edge gap of about 1/32 to 1/16 in, up to 1/8 in for thick safety film
SplicesAllowed when the glass is wider than the roll

Sources: IWFA, safety and security guide; IWFA, visual inspection

How it is calculated

Pane area = width x height; film area = area x identical panes, added up over every row. A pane over 40 sq ft (3.7 m²) is counted to check: without the film maker's own guidance, IWFA does not recommend a solar film on an annealed sealed unit of that size; check compatibility before installing. Each pane is cut across the roll, as many identical pieces side by side as the width holds, turned the way that takes less roll; a pane wider than the roll both ways is seamed, one strip of its long side per roll width. Rolls = roll length taken x (1 + waste) / roll length, rounded up to the roll: an estimate, panes of different sizes never share a row. No roll width or waste comes filled in: they are yours.

FAQ

How much window film do I need?

Add up each pane's width times height times how many: 12 panes of 4 x 5 ft and 6 of 3 x 4 ft make 312 sq ft of film. On a 60 in by 100 ft roll, one piece fits across: the 4 x 5 ft panes take 4 ft of roll each and the 3 x 4 ft ones 3 ft, 66 ft of roll, or 0.73 of a roll with 10% waste: 1 roll. Each piece is cut a little larger than the glass and trimmed in place, so lay the panes out across the roll width before you order.

Which panes should I check before installing solar film?

Without the film maker's own guidance, IWFA does not recommend a solar film on an annealed sealed unit over 40 sq ft (3.7 m²) or a single annealed pane over 100 sq ft (9.3 m²). The calculator counts the panes over 40 sq ft so you can check them: a 6 x 8 ft pane, 48 sq ft, counts as one. For thick, tinted, coated or partly shaded glass, check with the film maker's glass chart before installing.

Measuring every window of a building?

For window film installers and their crews: the window film templates below take every pane by facade and floor, the film by product, the frames and edges and the review notes, and put the totals in a PDF or Excel report for your bid. You can try them without an account.

The whole job in MesuPro

For window film and screen installers and their crews: every employee measures with the same form, the math is done as they type, and the office finds the sheet and its PDF or Excel report. 14-day free trial, no credit card.

Commercial window film⁠

Film for multi-story buildings, floor by floor: glass area, film product and linear elements.

You get: Glass Surface Area Total Area Panes over 40 sq ft

Window film⁠

Film for a house or a small building: windows, skylights and glass doors, film area per type, safety film anchoring.

You get: Total Area Panes over 40 sq ft Anchored length

Your trade isn't listed? The AI assistant builds your form.

Start your 14-day free trial

No credit card. Cancel anytime.

Did this page help you?

Feedback on this calculator

A result that looks wrong, a missing case, an idea? Tell us.

Please don't put personal details in this box.