Drywall survey
Walls and ceilings room by room, sheets, trim, compound, tape and screws, GA-214 finish levels, repairs and textured ceilings.
No credit card. Cancel anytime.
Feet and inches or metric: your choice. One switch on the sheet converts every measurement.


What you measure
The template's tables and their columns, as the app shows them. Calculated columns fill in as you type.
Walls and ceilings
- SurfaceChoices: Wall Ceiling Bulkhead or soffit Other
- Where
- Length
- Height or width
- Openings to deduct
- Board area calculated
- Board typeChoices: Regular Moisture-resistant Type X (fire-rated) Abuse-resistant Glass-mat tile backer Other
- ThicknessChoices: 9.5 mm (3/8 in) 12.7 mm (1/2 in) 15.9 mm (5/8 in) Other
- Product
- Sheet width
- Sheet length
- Waste
- Sheets calculated
- Crew hours
- Notes
Corners and trim
- ItemChoices: Outside corner bead L or J trim Control joint Other
- Where
- Trim length
- Product
- Piece length
- Trim pieces calculated
- Notes
Finishing materials
- Where
- Board area to finish
- Compound product
- Compound per area
- Compound calculated
- Tape per area
- Tape calculated
- Screws per area
- Screws calculated
- Level of this finishingChoices: Level 0 Level 1 Level 2 Level 3 Level 4 Level 5
- Area to skim coat calculated
- Notes
Repairs
- Location
- RepairChoices: Dent or small hole Hole over 2 in or water damage (new piece) Crack or loose joint Nail or screw pops Torn face paper Corner bead Other
- How many
- Cut-out width
- Cut-out height
- Board to cut calculated
- Tape around the new pieces calculated
- Crack or joint length
- Tape over the cracks calculated
- Fasteners per pop
- New fasteners for the pops calculated
- Level to matchChoices: Level 0 Level 1 Level 2 Level 3 Level 4 Level 5
- Fire-rated wall or ceilingChoices: Yes No To check
- Water damageChoices: None seen Dry, paper sound Loose paper or soft core
- Notes
Textured ceilings
- Room
- Ceiling length
- Ceiling width
- Ceiling area calculated
- TextureChoices: Popcorn (acoustic) Knockdown or stipple Swirl or stucco Other
- Painted overChoices: Yes No To check
- Asbestos testChoices: Not tested Sample at the lab Lab: none found Lab: asbestos found
- Method plannedChoices: Scrape and skim coat Cover with new drywall Paint over (encapsulate) Leave in place
- Wall height
- Floor and walls to cover calculated
- Crew rate
- Texture crew hours calculated
- Notes
See these tables calculate with your own measurements, no account.
Try this templateMore templates: Drywall
Suspended ceiling survey
Suspended ceilings room by room: tees, wall angle, hanger wires, 2 x 4 or 2 x 2 panels and the border panels.
You get: Ceiling area Wall angle run Wall angle pieces
Sound insulation: survey
Sound insulation work: walls and ceilings by location, treatment, sheets, damping, resilient channel, sealant and openings.
You get: Area Sheets Damping tubes
About this template
Measure the walls and ceilings of each room, get the sheets per product, the corners and trim, and the compound, tape and screws for the job from the makers' per-area rates, with the board type, level of finish and fire separation each room needs.
Guide and sources
Read the guide and sources
Rooms: measure each room on the floor, one row per wall and one per ceiling: a wall's length and height, a ceiling's length and width. "Add a room" adds the next one with its tables blank; "Add a section like this one" adds the next floor. Deducting openings is your call: CGC and CertainTeed count them as board, USG subtracts only the large ones.
Board: pick the type and thickness the spacing and the room ask for. NBC Table 9.29.5.3 and IRC Table R702.3.5 give the thickness by support spacing; Type X is the fire-rated core; moisture-resistant board is not for wet areas or directly behind tile in a shower, and tile around tubs and showers goes over a moisture-resistant backing (NBC 9.29.10.4, IRC R702.3.7). Type the sheet size from the product's data sheet and your waste: no maker publishes a waste figure. The sheets are exact on each row and rounded up once per product.
Fire separation: in Canada a house's own garage needs no fire separation, only an air barrier against fumes (NBC 9.10.9.18); suites are separated by 45 min, or by 12.7 mm board where a secondary suite allows it (9.10.9.16; Quebec limits that option to 3 units and 2 storeys). Table 9.10.3.1.-A rates stud walls (12.7 mm Type X one layer each side: 45 min). In the US, the garage side gets 1/2 in board and a ceiling under rooms 5/8 in Type X (IRC R302.6); an enclosed space under stairs 1/2 in (R302.7).
Finishing: in the Finishing section, type the board area once (the rooms' total, shown in the totals) and the rates from the data sheets: compound about 10 gal per 1,000 sq ft (USG; CGC prints 40.5 L/100 m²), paper tape about 370 ft per 1,000 sq ft, screws from the maker's tables (about 1,000 per 1,000 sq ft at 16 in framing). Beware of "per 100 m²" columns that repeat the per-1,000 sq ft numbers. The level of finish (GA-214, 0 to 5) sets how many coats go on. Fasteners follow NBC 9.29.5.8 and 9.29.5.9, IRC Table R702.3.5 and GA-216; ASTM C840 is the application standard.
Quebec: the Construction Code, Chapter I (the NBC 2020 modified for Quebec) applies since 2025-04-17; work begun before 2027-10-17 may still follow the previous edition. Its Quebec changes leave 9.29 as is and limit 9.10.9.16. In cold weather keep the space at 10 °C or more for 48 h before and after taping (NBC 9.29.5.10).
Older homes: Health Canada lists paint, putty, drywall, caulking, sealants and spackling among older materials that may contain asbestos, and lead paint is likely before 1960 (possible until 1990; the US EPA RRP rule covers homes built before 1978). Do not sand or break a suspect surface: only a laboratory test tells.
Levels and repairs: in Finishing, pick the level of each finishing scope; its help gives the coats GA-214 asks per level, and at level 5 the sheet shows the area to skim coat. A repair visit goes in Repairs, one line per repair or per group of identical ones: a hole over 2 in or a water-damaged area is cut out and closed with a new piece (USG), so type the cut-out size and the sheet adds up the board to cut and the tape around the pieces; a crack gets tape over its length; each nail or screw pop gets new fasteners about 1 1/2 in away (one for USG, CGC and CertainTeed, one on each side for National Gypsum). Say the level to match and whether the wall is fire-rated (CGC: no California patch there). No maker prints the compound for a repair: the sheet gives none.
Textured ceilings (popcorn, knockdown, stucco) have a section of their own, a row per room: the ceiling's length and width give its area; note the texture, whether it is painted over, the asbestos test as it stands and the method you plan. The sheet never says what the material holds: asbestos cannot be identified by sight, so the test comes before any scraping (EPA, Health Canada; in Quebec the CNESST deems gypsum and joint compounds made after January 1, 1980 asbestos-free). Painted texture in an older home also raises lead: EPA RRP in the US, Health Canada in Canada. The wall height gives the floor and walls to cover with plastic, and your crew's rate the hours. After scraping, put the skim coat in Finishing materials at Level 5; new board in Walls and ceilings.
Sources
- CertainTeed, installation guide Manufacturer data
- USG, installation guide Manufacturer data
- GA-223 Trade association
- IRC 2021, R702.3.7 Code
- National Gypsum, construction guide Manufacturer data
- IRC 2021, R702.3.5 Code
- GA-216 Trade association
- USG, all purpose compound Manufacturer data
- USG, paper joint tape Manufacturer data
- ASTM C840 paywalled Standard
- GA-214 Trade association
- EPA mold remediation guide, Table 2 Government
- EPA RRP Government
- EPA, asbestos Government
- IRC 2021, R302.6 Code
- IRC 2021, R302.7 Code
- EPA, RRP rule Government
- CGC handbook Manufacturer data
- NBC 2020, Table 9.10.3.1.-A Code
- NBC 2020, 9.29.10.4 Code
- CertainTeed, M2Tech Manufacturer data
- NBC 2020, 9.29.5.3 Code
- CGC, all purpose compound Manufacturer data
- CertainTeed, ready-mix compounds Manufacturer data
- NBC 2020, 9.29.5.9 Code
- CGC handbook, chapter 12 Manufacturer data
- Health Canada, asbestos Government
- Health Canada, lead paint Government
- NBC 2020, 9.29.2.1 Code
- NBC 2020, 9.10.9.18 Code
- NBC 2020, 9.10.9.16 Code
- NBC 2020, 9.29.5.10 Code
- CNESST, asbestos health programme Government
- RBQ, chapter I Government
Your trade isn't listed? The AI assistant builds your form.
No credit card. Cancel anytime.