How to measure a roof for shingles

Two ways to the real roof area: from the ground, with the footprint and the pitch, or on the roof, face by face. Then the edges, the waste, the squares and the bundles. A worked example and a free calculator are at the end.

What to bring

  • A long tape measure (100 ft) or a laser measure
  • A level and a short tape, or a pitch gauge, for the pitch
  • A sketch pad, or a MesuPro sheet on your phone, to note each face and each edge

Safety first: on a roof, use fall protection, never work alone, and stay off a wet, icy or windy roof. When in doubt, measure from the ground, from a ladder at the eave or from the attic: the method below works all three ways.

Step by step

  1. Sketch the roof from above

    Draw the roof as seen from above and give each sloped face a letter. A gable roof has two rectangles; a hip roof has two trapezoids on the long sides and two triangles at the ends. Mark the ridges, hips and valleys, the dormers and the porch roofs: every small face counts, and every line takes its own material.

  2. From the ground: the footprint and the overhangs

    Measure the walls of the house, then the overhangs: from the wall to the outside of the fascia at the eaves, and to the outside of the trim at the gable ends. The plan area of the roof is the footprint with the overhangs added on every side: a 38 x 26 ft house with 1 ft overhangs gives 40 x 28 ft. When every face has the same pitch, gable or hip, the sloped area of the whole roof is that plan area times the pitch factor.

  3. On the roof: face by face

    Measure each face along the eave, then its slope length from the edge of the eave up to the ridge (on a gable roof, along the rake). Width x slope length is the face's area, with no pitch factor; on a trapezoid or a triangle, take the average of the bottom and top edges as the width. The MesuPro template takes the slope length when you enter one, or the horizontal run x the pitch factor, whichever is larger.

  4. Find the pitch

    The pitch is the rise for 12 of run. Rest one end of a level on the roof or on a rafter and hold it level, mark 12 in from that end, then measure the vertical distance between the level and the roof at that mark: that is the pitch (6 in means 6/12). From the attic, do it on a rafter; a pitch gauge reads it directly. Check each face: a porch or an addition often has its own.

  5. Turn plan measurements into sloped ones

    The pitch factor is the square root of 1 + (pitch / 12)²: the sloped length for each foot of horizontal run. A plan area times the factor gives the real area (table below). Hips and valleys run at an angle in plan, so their length has its own factor: the square root of 2 + (pitch / 12)², times the run, when both faces share the pitch.

  6. Measure the edges

    Note the length of each line, on the roof or from the plan: the eaves (drip edge, starter strip, ice barrier), the rakes (drip edge), the ridges and the hips (ridge cap) and the valleys. Where ice forms along the eaves, the IRC runs an ice barrier from the eave to at least 24 in inside the exterior wall; the NBC asks for eave protection at least 900 mm up the slope and 300 mm past the inside face of the wall, except on steep roofs, wide overhangs and mild climates.

  7. Add the waste, then count squares and bundles

    The waste covers the cuts: Owens Corning plans 10 to 15% as a rule of thumb, more on roofs with hips, valleys and dormers; no association publishes a waste table. Squares = area with waste / 100 sq ft. Most shingles come 3 bundles per square (some heavy ones 4 or 5: read the wrapper). The starter strip and the ridge cap are bought apart, by the linear foot on their wrappers: 20 to 45 ft of ridge per bundle, about 100 to 123 ft of starter for most products.

Pitch factors (reference)

Computed for each pitch: the roof factor, square root of 1 + (pitch / 12)², turns a plan area or a run into the sloped one; the hip or valley factor, square root of 2 + (pitch / 12)², gives a hip's length from its run when both faces share the pitch.

PitchRoof factorArea addedHip or valley factor
2/121.0141.4%1.424
3/121.0313.1%1.436
4/121.0545.4%1.453
5/121.0838.3%1.474
6/121.11811.8%1.500
7/121.15815.8%1.530
8/121.20220.2%1.563
9/121.25025.0%1.601
10/121.30230.2%1.641
11/121.35735.7%1.685
12/121.41441.4%1.732

Computed from the pitch, as in the MesuPro roofing template.

The calculation

Pitch factor = square root of (1 + (pitch / 12)²). Real area = (width - narrowing at the ridge / 2) x the larger of the slope length and the horizontal run x pitch factor, face by face: with a slope length, no pitch is needed. The first factor is a trapezoid's average width; a narrowing equal to the width gives a triangle, no narrowing a rectangle. Area with waste = real area x (1 + waste), each face with its own: 10% to start, the rule of thumb the template gives (Owens Corning: 10 to 15%, more on a cut-up roof). Squares = area with waste / 100 sq ft. Bundles = squares x bundles per square: 3 for most shingles, 4 or 5 for some heavy designer shingles (check the wrapper). Underlayment rolls = real area / roll coverage. Ridge cap bundles = ridges and hips / coverage per bundle. Drip edge = (eaves + rakes) / 9 ft 10 in: a 10 ft piece laps the next by 2 in (IRC R905.2.8.5). Starter bundles = starter length / coverage per bundle. Eave membrane = eaves x its depth up the slope, then rolls = that area / roll coverage. Each count is rounded up once, on the total. No coverage comes filled in: read it on the wrapper.

Worked example

A hip roof 40 ft by 28 ft at the fascia, 6/12 all around, with 10% waste. Every face rises over a 14 ft run (half of 28 ft), and the four faces' average widths add up to 80 ft (26 + 26 + 14 + 14): the roof works as one face 80 ft wide, whose plan area is the footprint. With the 6/12 factor of the table above, real area 1,252.2 sq ft, 1,377.4 sq ft with waste, 13.77 squares, so 42 bundles. Its four hips are 14 x 1.5 = 21 ft each and its ridge 40 - 28 = 12 ft: 96 ft of ridge cap.

Common mistakes

  • Using the flat (plan) area: a 6/12 roof is about 12% larger than its footprint, a 12/12 roof about 41%.
  • Leaving the overhangs out of the footprint, the run or the width.
  • Taking a hip or a valley as long as its run: on a 6/12 roof it is 1.5 times longer.
  • Counting the starter strip and the ridge cap in the bundles per square: they are bought apart.
  • Mixing feet and inches: 14 ft 6 in is 14.5 ft, not 14.6.
  • Leaving out small faces: dormers and porch roofs add up.

Roofing: from the slope to the bundles

The whole job in MesuPro

Roofing: measurement and materials⁠

Real sloped area from the pitch, squares, shingles, underlayment, ridge cap and drip edge.

You get: Real area Area with waste Squares

Your trade isn't listed? The AI assistant builds your form.

Start your 14-day free trial

No credit card. Cancel anytime.