Free gutter calculator: downspouts, hangers, elbows and straps

Get the downspouts, hangers, elbows and straps for your gutter runs in seconds, free and without an account. One row per gutter run: its length, its outlets, the drop of its downspouts and, optionally, the roof area draining to it. Enter your spacings: the calculation counts the rest.

How to fill it in

One row per gutter run: its length, its outlets, the drop of its downspouts and, optionally, the roof area draining to it. Enter your spacings: the calculation counts the rest.

Units
Feet and inches

Run 1

ft
ft
sq ft
in
ft

Result

Fill in the fields to see the result.

A quick estimate, with no rainfall flow: sizing by rainfall follows the plumbing code. The template handles the whole job: sizes, end caps, corners, discharge, old gutters and guards.

The whole job, not only this calculation

For gutter installers and their crews, the template does what this page cannot: the whole job on one sheet, every measurement on its own line, saved in the client's project with a PDF or Excel report.

Spacing and lengths: the makers' figures (reference)

What the makers' installation guides say, cited as a guide: your spacing stays yours.

GentekAmerimax
HangersAt most 800 mm (31 in) apartOne every 24 in, every 18 in where ice and snow are heavy
Downspout strapsOne next to the upper elbow, then at least every 3 m (10 ft)2 bands per 10 ft section
SlopeAt least 1/4 in per 10 ft (6 mm per 3 m) toward the nearest outletAbout 1/4 in per 10 ft toward the downspout
Lengths sold3 m and 6 m gutters, 3 m downspouts (French edition)Gutters and downspouts in 10 ft lengths

Sources: Gentek installation guide; Amerimax metal gutter guide

What one downspout serves (reference)

Two guides for placing the outlets. To size by rainfall, the plumbing codes start from the roof area in plan (Canada adds half of the largest wall that sheds water onto it).

One downspout
GentekUsually enough for 475 to 600 sq ft (45 to 55 m²) of roof
SMACNAAt most 50 ft (15 m) of gutter, in practice, because of thermal expansion

Sources: Gentek installation guide; SMACNA calculator; IPC 2021, 1106

Where the water goes: check your city's rule (reference)

Downspout discharge is up to each city. A few rules, as read: yours may differ.

PlaceRule as read
US (IRC 2021)On expansive or collapsible soils: roof water discharges at least 5 ft (1524 mm) from the foundation walls, or into an approved drainage system
PortlandVoluntary disconnection: the end of the extension at least 6 ft from a basement and 5 ft from the neighbor's property line, among others
TorontoNo downspout connected, directly or not, to a storm or combined sewer (an exemption can be requested)
MontrealOnto a permeable surface (flower bed, lawn) at least 1.5 m from the foundation; never into the foundation drain, toward a hard surface or the street

Sources: IRC 2021, R801.3; Portland, downspout disconnection; Toronto Municipal Code 681-11S; Ville de Montréal, gouttières

How it is calculated

For each run: hangers = length / spacing, rounded up, + 1. Each outlet has its downspout, of the drop height entered: downspout length = outlets x drop. Downspout to buy, in the 10 ft lengths sold (3 m in meters): each drop takes its whole lengths, and what is left of it is cut from one length, two of those rests sharing a length when they fit in it; a rest is never pieced from two offcuts. The template counts them the same way, row by row: the rests of two rows never share a length there. Straps = downspouts x (drop / strap spacing, rounded up, + 1). Elbows = downspouts x elbows per downspout. Roof per downspout = the run's area / its outlets, and gutter per downspout = length / outlets: the calculation shows the most loaded run and the longest. No spacing comes filled in: they are yours.

The whole job in MesuPro

For gutter installers and their crews: every employee measures with the same form, the math is done as they type, and the office finds the sheet and its PDF or Excel report. 14-day free trial, no credit card.

Gutter survey⁠

Runs by size, hangers, end caps, corners and outlets, downspouts with elbows and straps, old gutters, gutter guards and heat cables.

You get: Hangers Roof area per outlet Downspout length

Your trade isn't listed? The AI assistant builds your form.

Start your 14-day free trial

No credit card. Cancel anytime.

Did this page help you?

Feedback on this calculator

A result that looks wrong, a missing case, an idea? Tell us.

Please don't put personal details in this box.